About Spray.Bike Paints

We are pleased as punch to offer Spray.Bike paints! 

A groundbreaking range of bicycle-specific color coating designed for both amateur and professional use. The paint is a dry matte powder-coating that doesn’t drip, dribble or misbehave in any way.

Perfect for customizing, repairing, restoring or revitalizing your electric bike!

Solid colors tech spec

  • Highly pigmented acrylic paint compound
  • Dry-fall powder coating
  • Non-drip, non-dribble formula
  • Suitable for steel, aluminum and carbon surfaces
  • Permanent and resilient: UV-resistant and weather-resistant
  • Deep matte colors
  • Easily-achieved fading, stenciling and blending effects (see below)
  • Requires no post-application equipment or heat treatment
  • 400ml and 200ml options
  • 1 x 400ml can will cover a frame and fork in a single coat
  • Minimum recommended coats: one

Instructions for use

  • Ensure surface is clean and dry
  • Primer is not required but is recommended
  • Wear protective gloves, protective clothing, eye/face protection
  • Always paint in an open space in the open air
  • Shake can for at least 3 minutes before use
  • Test spray for 2-3 seconds prior to application
  • Optimal temperature for spraying: 20-25°C. Do not use Spray.Bike if the temperature is below 10°C or above 35°C, or if relative humidity is above 75%
  • Always spray with the can in a vertical position, otherwise the paint might 'spit' unevenly
  • Solid colors: spray surface from a distance of 2-4 inches (5-12 cm)
  • Pocket Clears, Frame Builder’s Smoothing Putty, Frame Builder’s Transparent Finish, Frame Builder’s Cold-Zinc, Frame Builder’s Metal Primer, Frame Builder’s Carbon Primer, Frame Builder's Metal Plating: spray surface from a distance of at least 20 cm
  • Keirin Flake and Keirin Sunlight: spray surface from a distance of at least 30 cm
  • Frame Builder’s Top Wax: Spray onto a paper towel or soft lint-free cloth and apply gently
  • When spraying, keep hand moving at all times
  • Allow to dry before adding 2nd coat (touch dry: 10 minutes, complete cure: 2 hours)
  • Do not use isopropyl alcohol over paint
  • At end, turn can upside down and spray for 2 seconds before storing
  • Protect can from sunlight and temperatures exceeding 50°C/122°F
  • For a satin or gloss top-coat, finish with Spray.Bike Frame Builder's Transparent Finish - Satin/Gloss. 
  • For ongoing protection (whether the finish is matte, satin or gloss), regularly apply the Frame Builder's Top Wax
  Spray distance
All solid colors 5-12 cm

Pocket Clears
Frame Builder’s Cold-Zinc
Frame Builder’s Metal Primer
Frame Builder’s Carbon Primer
Frame Builder’s Smoothing Putty
Frame Builder’s Transparent Finish
Frame Builder's Metal Plating

at least 20 cm
Keirin Collection at least 30 cm
Frame Builder’s Top Wax spray onto paper towel or lint-free cloth and apply gently

    Prep
    Spray.Bike paint will adhere to most raw metal and painted surfaces without any major pre-prep. However, if painting over an existing paint job, a bit of prep work will provide the best surface for adhesion. We recommend wet sanding with 800, being mindful to get the tricky spots, to rough up the surface and a good cleaning with soap and water prior to painting. 
    Always ensure that all surfaces are completely clean and grease free. Any micro-film left from degreasers or cleaning products can create a barrier preventing Spray.Bike from adhering properly. NEVER use acetone or a product containing acetone, as this is guaranteed to weaken Spray.Bike.
    A pure medical alcohol is recommended for the ultimate pre-paint cleaner - but do make sure all reside is removed with lint free rags.

    Using the Frame Builder's Prep & Finish range
    Click here

    Spraying
    It’s essential that you understand and follow the spray distances. These are the distances from the can in your hand to the metal being sprayed. They vary depending on the product:

    • Solid colors (BLB, Pop, Historic, Vintage, Fluorescent, Pocket Solids): 5-12 cm
      As Spray.Bike cans are pressurized, there’s an optimum distance at which the paint is effective on leaving the nozzle: 5-12 centimeters. In this ‘window’ the paint is semi-wet and the pigment is perfectly primed to do its job properly. Under 5 centimeters, faults can occur. After 12 or 14 centimeters the paint will have turned into a dry powder dust with little adhesion at all.

    • Pocket Clears, Frame Builder’s Smoothing Putty, Frame Builder’s Transparent Finish, Frame Builder’s Cold-Zinc, Frame Builder’s Metal Primer, Frame Builder’s Carbon Primer, Frame Builder's Metal Plating: at least 20 cm

    • Keirin Flake and Keirin Sunlight: at least 30 cm

    • Frame Builder’s Top Wax: Spray onto a paper towel or soft lint-free cloth and apply.

    Spray.Bike cans must always be held vertically while spraying. When the can is horizontal, the gas propellant rather than the paint is driven into the nozzle, creating a high-pressure paint spit that will land unevenly as lumps.
    Always move your hand continuously while spraying, as this ensures an even coating. Touch-ups can always be done later – don’t over-apply the paint in a single coat.
    If re-using the paint after storage, test spray first. If the paint seems to splatter, replace the nozzle as the existing one is probably clogged.

    Polishing
    For best results, always polish Spray.Bike solid colors with parchment paper or a lint-free soft cloth. A gentle pressure and polish action will compact the paint’s surface for greater strength. This is best done before the paint has completely cured, so polish within two hours of spraying. Be more careful where colors meet in order to avoid physically forcing colours to bleed.

    Drying
    For best results, don’t be impatient! Although the coating does seem to dry rapidly (touch dry in a few seconds), it’s always best to let the paint completely dry over a 12 hour period before re-building the bike.

    Dealing with problems
    Getting areas where the paint has landed as a powder (and has a rougher surface) will happen – but this is easily solved. Leave the paint to completely dry, then using a soft cloth rub gently to smooth the surface.
    If you do make a mistake (e.g. put color in the wrong place or over-apply the product), wait for the spray to completely dry (max 2 hours). Then using a very fine sandpaper or other abrasive material, slowly rub away the paint. Don’t use a traditional solvent paint remover though as it will damage the acrylic compound in Spray.Bike and you’ll end up making more mess. Do not use isopropyl alcohol at any point on the paint. Remember that the spray distance for the solid colors is 5-12 cm, whereas the spray distance for the Pocket Clears, Frame Builder’s Transparent Finish, Frame Builder’s Smoothing Putty, Frame Builder’s Cold-Zinc, Frame Builder’s Metal Primer, Frame Builder’s Carbon Primer and Frame Builder's Metal Plating rangeis at least 20 cm. For the Keirin Collection, it's at least 30 cm. 
    The Frame Builder’s Top Wax shouldn't be sprayed directly onto the frame. Instead, spray onto a paper towel or soft lint-free cloth and apply gently.

    Dealing with stickers and decals

    Old stickers that you can't remove and want to paint over:

    cover with the Frame Builder's Smoothing Putty before you paint

    Old decals that you want to paint over:

    just paint over them

    New stickers or decals:

    set on top of your new paint-job and then seal with the Frame Builder's Transparent Finish

    Note: in vary rare circumstances, the acetone in the Transparent Finish can affect the ink in a decal or sticker. To check this, spray a small amount of Transparent Finish onto a test decal/sticker. If it melts the ink or the ink runs, you'll have to place the actual decal/sticker over the Transparent Finish on your frameset.
    Be aware that the Matte Transparent Finish adds an opaque textured layer when sprayed onto a clear surface, so don't spray onto stickers or decals with a transparent backing  unless you want that transparent backing to have a frosted, opaque effect. 

    Using the Fluros
    Because of the reflective pearlescent particles, the fluro colors are slightly grainier than the other ranges. A base coat of Whitechapel / Marylebone or Metal / Cold -Zinc Primer is HIGHLY RECOMMEND to make the fluorescent color pop. Rubbing down about an hour after painting with a soft cloth or parchment paper is recommended to help compress the paint. 

    Using the Pocket Clears
    These are perfect for creating a glaze on raw metal tubing, subtly changing a base colour, fades and shades (see blending below).
    Remember that although the spray distance for the solid colors is 5-12 cm, for these Pocket Clears, because they contain the Frame Builder’s Transparent Finish, the spray distance is at least 20 cm.

    Using the Keirin Collection
    The Flake range consists of 6 colored metal flake options in our Frame Builder’s Transparent Finish. They can be used over Spray.Bike colors to provide an amazing glitter finish – or even used over factory paint to add a unique sparkle effect to the frame.
    The Sunlight range has 4 colors of crushed liquid glass in the Frame Builder’s Transparent Finish, creating a glitter effect only really viewable in direct sunlight.
    All colors can be overlaid to create specific color flake mixes.
    2 coats recommended.
    Remember that the spray distance is much further than all our other products: at least 30 cm.

    Masking and stenciling
    Click here

    Blending
    Use the Pocket Clears for blending as they can produce rapid and unusual color change when used in conjunction with (i.e. on top of) solid colors (especially Fluro Clears on top of solid Fluro colors).
    The Pocket Clears are a solid pigment with a transparent base layer, so the final color is based on the combination of solid/clear used, e.g. Fluro Yellow Clear on top of a blue will become a green.
    Use on junctions where 2 dramatic colors meet to create a fade. Give it a bit of practice for great results.
    Note: with the Pocket Clears, spray the surface from a distance of at least 20 cm.

    Using the Frame Builder’s Prep & Finish range
    Click here

    Storage
    Spray.Bike paint lasts in its can for up to 10 years.
    Store upright and below 50°C so it will always be there for scratches and touch-ups.

    Inspiration
    Need some inspiration before you start?
    Click here for pics of the fantastic things people are doing with Spray.Bike all round the world
    Click here for some inspirational and instructional vids